Page 1:
Vehicle GPS Tracker
(GPS+GSM+SMS/GPRS)
GT02D User Manual
(Version 9.9)
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully before
using this product. Please note that specification and information are
subject to changes without prior notice in this manual. Any change will be
integrated in the latest release. The manufacturer assumes no responsibility
for any errors or omissions in this document.
Page 2:
1. Summary
Working Based on existing GSM/GPRS network and GPS satellites,
this product can locate and monitor any remote targets by SMS
or internet.
Overview of the characteristics:
1.GPS position.
2.GSM 850/900/1800/1900MHZ.
3. Wide voltage range:9-40V.
4. Oil-cut function.
5. GEO-Fence alarm.
6. ACC alarm.
7. Vibration alarm.
8. Power-Cut alarm.
9. Overspeed alarm.
2．Accessories：
Power line:
Page 3:
Relay:
Manual:
Screws:
Page 4:
3. Spec：
1）.GSM：850/900/1800/1900MHZ
2）.GPRS: Class12, TCP/IP
3）.Working Voltage：9-40V DC
4）.Working current：≈22mA (12VDC)
5）.Working current：≈12mA (24VDC)
6）.GPS locating time：Cold start≈38s（Open sky）
Warm start≈32s
Hot start≈2s（Open sky）
7）.GPS Precision：10m（2D RM）
8）.Working temperature：-20℃～+70℃
9）.Working humidity：20%～80%RH
10）.Measurement：90(L) x 45(W) x 13.5(H) mm
Page 5:
4.Device status indicators
Power Status (Red LED)
Continuously Bright
External Power
Connected
Continuously Dark
External Power Cut-off
GPS Indicator (Blue LED)
Continuously Bright
GPS Unfixed
Flashing
GPS Fixed
GSM Indicator (Green LED)
Continuously Bright
No GSM Signal
Flashing
GSM Signal OK
5.Installation
5.1 Preparation before installation
5.1.1 Open the packing box to check whether the type of device is correct
and whether the accessories are included.
Page 6:
5.1.2 This product is a high-tech electronic device, installation should be
undertaken by a professional.
5.1.3 Please follow the following procedures to install your GT02D.During
installation, there should be no power to the device.
5.1.4 Installing SIM card:
The device need to insert a SIM card which support GSM 2G network. The SIM
card used should be enabled for GPRS.
1) Testing SIM card: to test SIM card, please install it into a normal
GSM mobile and ensure it can send and receive SMS, and enables for
GPRS.
2) Installing SIM card: Remove the upper cover of device, insert SIM card
as shown then replace cover, lock the shell with 4 bolts
.
.
5.2 Installation
Page 7:
The GPS tracker must be installed under professional personnel.
Note：
1) Please install the device in the hidden place as followings：
Under Front windshield；
In the front instrument panel；
Under back windshield；
2) Avoid being placed with signal radiators like reverse sensor ；
3) The device has GSM antenna and GPS antenna inside. Please ensure the
receiving side of the device is face up and without metal cover.
Note: The metal cover will lessen the receiving of GPS signals.
5.3 Selecting installation place and fixing it.
There are two kinds of installation: covert and non covert.
5.3.1 If you need the covert installation, please refer installation to an
auto electrical contractor.
Note:
1) To prevent theft of the GT02D, the device should be installed as
covertly as possible.
2) Avoid placing the GT02D close to higher power electrical devices, such
as reversing radar, anti-theft device or other vehicle communication
equipment.
Page 8:
3) The GT02D should be fixed into position with cable ties or wide
double-side tape.
4) Your device has built-in GSM antenna and GPS antenna. During
installation, please make sure the receiving side face is up, with
no metal object above the device to interfere with GPS reception. The
following places are suggested for installation:
Under the dash board below the front windshield;
- In the parcel shelf in the rear;
- In the front bumper( non-material face), please ensure the device cannot
get wet;
- Under the wiper version (non-metal), please ensure the device cannot get
wet;
Page 9:
Notice: If the windshield is pasted with metal thermal-protective coating,
it may affect the performance of the device. In this case, please change the
installation place after consulting the professional.
5.3.2 Non Covert Installation,
Firstly fix the device on the dash board below windshield.
- In the parcel shelf in the rear;
- In the front bumper( non-material face), please ensure the device cannot
get wet;
- Under the wiper version (non-metal), please ensure the device cannot get
wet;
Notice: If the windshield is pasted with metal thermal-protective coating,
it may affect the performance of the device. In this case, please change the
installation place after consulting the professional.
6. Device wiring requirements
6.1 The device power supply is DC 9-40V. The red line is positive pole while
Page 10:
the black line is negative pole.
6.2 The negative pole of power supply connects with ground or the metals.
Please do not connect with other ground lines.
6.3 When finishing the power supply wire connection, please make the plug
of power supply to the device.
7.The Device Working
7.1 Power on:
Connecting to the power, then switch on the device (in the board of the tracker, there
a switch). The 3 LED will light. The device will upload the data to the online platform
by Sim card, the default data-upload time interval is 15seconds. When the car is in
static state for 5 minutes, the device will come in energy saving mode.
7.2 Power off：Pull off the power wires plug then switch off the device.
Page 11:
8.User Settings
8.1 SMS Commands Instruction
1)Center Number
Text command
Parameter
Sample
CENTER Add
710#number#
711#number#
710#008613500135000#
711#008613800138000#
CENTER Del
D01#
D02#
D01#
D02#
Command
Description
1)Center numbers can control the oil and power and
resume factory setting
2) Center numbers can receive the call and text of
See AlsoWhat is the red H2O light on a Whirlpool refrigerator? - Chef's Resource1726 Stonecrest Dr, Houston, TX 77018 - MLS 46154076 - Coldwell Banker2304 Longfellow Street, Detroit, MI - 4 Beds - For Sale - $415,000 - The Agency Global Boutique Real Estate Brokerage2414 Bedford Park Dr Henderson NV 89052 MLS 2590639Alarms from tracker
3) Only 2 numbers can be center numbers.
4) The number should be your mobile phone number, should
not be the sim card number in the tracker.
5) Please add country code, for example, send SMS as:
Page 12:
710#008613800138000#,0086 is China code.
2) View Administrator Number
Text command
Parameter
Sample
View
901#
901#
Command
Description
This SMS command is used to view Device center number.
Command
Feedback
Successful reply：Admin1:
Admin2:
3)Authorized Number Set
Text command
Parameter
Sample
Authorized
Add
101#number#
102#number#
103#number#
1：101#008613800138000#
2：102#008612345678912#
3：103#008612345678912#
Page 13:
Authorized
Del
D11#
D12#
D13#
D11#
D12#
D13#
Command
Description
1) Authorization number for SMS control oil.
2) only three numbers to set the authorization number
3) The number should not be sim card number in the
tracker.
4) Please add country code, for example, send sms as:
710#008613800138000#
Command
Feedback
Successful Setting：Add Authorization account 1
OK!
4) View Authorized Number
Text command
Parameter
Sample
View
C10#
C10#
Page 14:
authorized
Command
Description
This directive is used to view the equipment
authorization numbers
Command
Feedback
Successful Setting：
Authorization 1：
Authorization 2：
Authorization 3：
5)APN Setting
Text command
Parameter
Sample
APN Setting
802#username#pass
word#
1：802#intenet#123#123#
2: 802#internet#
Command
Description
APN differs according to the local telecom operators.
For example：APN request password ， please refer to
Sample 1，and Sample 2 for no password.
Command
Successful Setting：SET APN OK！
Page 15:
Feedback
6) Set / View Server
Text command
Parameter
Sample
SERVER
Parameter
803#SERVER#port#
803#47.90.39.27#6100#
803#gps.dyegoo.net#6100#
View SERVER
804#
CIP#
804#
CIP#
Command
Description
Change the IP and port when move to a new server
port：10~65535
Command
Feedback
Successful Setting：set IP OK!
7)Moving Time Interval
Text command
Parameter
Sample
TIMEER
730#uploading interval#
730#20#
Page 16:
Parameter
setting
Command
Description
Time scope：0，10~60 seconds； 0,no data uploading；
10~60,means time interval ；the default value is 15
seconds.
Command
Feedback
Successful Setting：SET TIMER OK！
8)Static Time Interval
Text command
Parameter
Sample
STATIC
731#time interval#
SUP#time interval#
731#5#
SUP#5#
Command
Description
Range：1~60 minutes；The device has
3D transmission and the default time interval are 5
minutes.
Command
Successful Setting：SET STATIC TIME OK！
Page 17:
Feedback
9) Cancel the continuous upload
Text command
Parameter
Sample
NUP
740#
NUP#
740#
NUP#
Command
Description
This command is used to cancel sending data to the
platform
If need to restore the uploading, please set upload
interval time setting.
Command
Feedback
SET OK！
10)Power-Cut
Text command
Parameter
Sample
RELAY
222#
222# cut off oil and power
Page 18:
Parameter1
RELAY
Parameter2
333#
333# recover oil and power
Command
Description
The device only cut off the oil circuit on the condition
of the driving speed below 20KM/H or in static state.
Command
Feedback
Cut Oil OK
The speed is high Cut Oil fail
Recovery Oil OK
11)GMT
Text command
Parameter
Sample
GMT
801#TIME ZONE#
801#E8#
801#W5#
Command
Description
The default time zone is 0.
Page 19:
12)Vibration Alarm (Default: Closed)
Text command
Parameter
Sample
VIBRATION Parameter
123#2#alarming way#
1) 123#2#3#
Set come into
vibration alarm
time
V123#2#
1) V123#2#
2) V123#1#
Enable vibration
Alarm
911#
911#
Disable vibration
Alarm
456#
456#
Command Description
the sensitivity value of the vibration is from
1 to 5，1 is the most sensitive and 0 is close.
Alarming ways: 1, calling 2, texting, 3 calling
and texting.
Page 20:
Command Feedback
set vibration alarm level，OK!
13)ACC Alarm (Default: Closed)
Text command
Parameter
Sample
Enable
840#Alarming Way#
840#1#
840#2#
840#3#
Disable
840#0#
840#0#
Command
Description
It can not be set when ACC on. Reply: ACC（set up fail!
pls turn off ACC）
Alarming ways: 1, calling 2, texting, 3 calling and
texting.
Command
Feedback
open ACC alarm OK
close ACC alarm OK
14)ACC Alarm & Vibration Alarm Open/Close
Text command
Parameter
Sample
Page 21:
Enable
110#
110#
Disable
111#
111#
Command
Description
This command is used to control ACC Alarm and vibration
Alarm at the same time. (When ACC is high,please refer
to 13 ACC alarm) both alarms are in Alarming way 3.
Command
Feedback
Open ACC & Vibration Alarm OK
Close ACC & Vibration Alarm OK
15)Over-Speed Alarm (Default: Closed)
Text command
Parameter
Sample
SPEEDING
Parameter
667#120#alarming way#
SSA#120#alarming way#
1)667#120#3#
667#120#
2)SSA#120#3#
SSA#120#
Command
Description
The speed scope is form 60-220, if the speed is no this
cope, the alarm is off.
Page 22:
Alarming ：1, calling 2, texting, 3 calling and texting.
Must set the center number.
Command
Feedback
Set speed-2 OK / Cancel speed OK
16) GEO-fence Setting
Text command
Parameter
Sample
Setting
920#radius#way#
920#1#2#
Cancel
921#
921#
Command
Description
Setting Geo-fence alarm, radius from 1-100, Unit: 100
meter.
Alarming ：1, calling 2, texting
Out Geo-fence 1 time, the Geo-fence canceled.
Feedback
Set Enclosure-2 OK / Cancel Enclosure OK
17)Reset
Page 23:
Text command
Parameter
Sample
RESET
930#
930#
Command
Description
Reset the device
Command
Feedback
Successful Setting：Reset system, ok!
18)Factory
Text command
Parameter
Sample
Parameter
940#
940#
Command
Description
Restore the factory setting
Only center number can initial this function
Factory setting will recover to the original setting
Command
Feedback
Successful Setting：FACTORY OK！
Page 24:
19)Language Setting
Text command
Parameter
Sample
LANG
Parameter
LANG1#
LANG0#
LANG1# 1:CHINESE，
LANG0#：ENGLISH
Command
Description
；When check the location, it will reply the Chinese
location in Chinese language setting; while reply the
URL link when in English language setting.
Command
Feedback
Successful Setting：SET LANG OK！
20)Position
Text command
Parameter
Sample
WHERE
988#
988#
Command
Description
Check the longitude and altitude and other
information of the device
Command
Reply with longitude and altitude, speed and IMEI.
Page 25:
Feedback
21)Google Link
Text command
Parameter
Sample
WHERE
666#
666#
Command
Description
Reply Google link with Latitude, Longitude, IMEI, ETC.
Command
Feedback
Google Link
22)Version
Text command
Parameter
Sample
VERSION
V00#
V00#
Command
Description
The command is to check the software version
Page 26:
Command
Feedback
VERSION:xxxx
BUILD:2018-07-05 10:12
23) Parameter Check
Text command
Parameter
Sample
Parameter
886#
886#
Command
Description
The command is to check the settings and the default
parameter.
Command
Feedback
IMEI:351190012535936
APN : cmnet
IP:IP and port
TIMER: moving uploading interval
STATIC: static uploading interval
CENTER: center number
LANG: language(CN/EN)
GMT: time zone (E/W8)
Page 27:
24)Status Check
Text command
Parameter
Sample
Status
902#
902#
Command
Description
The command is designed for checking the device’s
working status.
Command
Feedback
External power:ON/OFF
GSM Signal:HIGH/MIDDLE/LOW
GPS:FIXED/UNFIXED
RELAYER:DISABLE/ENABLE
Vibrate Warning:ON/OFF
Pause:ON/OFF
25)Set Low-battery/External power Alarm(Default Enabled)
Text command
Parameter
Sample
Disable
555#
555#
Enable
556#
556#
Command
Feedback
close low/Disconnect power OK
Open low/Disconnect power-2 OK
Page 28:
9. Platform
Website: http://www.dyegoo.net
Please click English to change to English language.
Login as Account or ID, Account is same as ID(IMEI last 11bits),ID is in
the label on the tracker.
Enter ID(IMEI last 11bits)
Password:123456
APP: http://www.dyegoo.net/app/
Page 29:
When download, please click UK flag to change to English.
For some Android mobile phone,it is needed to install
GoogleServicesFramework.apk, if there no this APK,it can not display
google maps in APP.
Please search GoogleServicesFramework.apk by google and install it
first,then install DYEGOO Google maps app.
In production, IP,port have been writed in, normally the tracker
will be auto online, if the tracker offline, Please set APN by sms command.
Please get APN from mobile operator of sim card inserted in the tracker.
If you lost IP,port,please send below sms command by admin number to
set them back：
803#gps.dyegoo.net#6100#
Or
803#47.90.39.27#6100#
10.Trouble shooting
10.1 The device is not online or offline on the web platform.
10.1.1 First, please check the three LED working state. If
possible. You can call the device’s number to check.
● If not connected, the device is out of signal. If the GSM
signals cannot reach your location, please drive to the open
sky.
If reminding the device SIM card is out of deposit, please make
deposit by the telecom operator.
● If you can connect to the device when calling, the SIM card has
deposited and please check with your operator for GPRS function. You
also can check by searching the internet on your mobile phone.
● If reminding the device is power off, please turn back the device
and proceed as followings:
a)Check if the red LED is in flashing. If the LED is dark, please
check the power connecting. If fuse is broken, please return the
Page 30:
device to the seller.
b)If the green GSM LED is not in constant flashing, please check the
installation of SIM card.
c)If the blue GPS LED is not constant light, it mean GPS signal can
not be received well, please check installed position.GPS signal
only can be received out of the room and face to sky.
10.1.2 Please check the offline area in order to judge if the network
problem of operators.
10.2 When GPS can not receive the signals, please drive in the open sky
and ensure there is no metal thins on the device.
10.3 When the device can not receive the GSM signal, please check the
SIM card installation. If the GSM signals can not reach your location
(such as the basem*nt), please drive to the open sky.
